We have found this post relating to How to Install a Bathtub listed below on the net and figured it made good sense to share it with you here.
Installing a tub isn't precisely rocket science, but it does require solid plumbing, woodworking, and also sometimes, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably difficult job. If the old tub is easily obtainable, the task can move rapidly; if you have to open up a wall to get rid of the old tub and also place the brand-new tub, the task is much harder. In either instance, the job is within a home handyman's abilities, although you will certainly need a helper to leave the old bathtub and also embeded in the brand-new one. Ensure you have actually certified yourself for the job and also fit attempting it. Rather than employing a service provider to take over a halfway-completed task, it is much better to consider utilizing one prior to you begin. Possibilities are you might require a specialist plumber to make tube links.
This post will certainly help you set up a new bathtub in your shower room if you have actually already purchased a new tub and also do not need to transform the plan of your previous water system pipes.
Your tools and also material checklist must comprise the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your setup, after that the first thing you ought to do is separate the water system. After doing so, turn on the faucets to drain pipes any kind of water continuing to be in the system. The process of removing the existing faucets can be fairly problematic due to the limited gain access to that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the taps. Have a fabric all set for the staying water that will certainly originate from the pipes. As soon as the supply pipelines have been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single faucets from transforming during this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any old sealing compound.
Before going on to fit the new taps, compare the pipeline connections on the old faucets to the brand-new taps. If the old taps are longer than the new taps, after that a shank adapter is required for the new taps to fit.
Fitting New Touches
If the tails of the new taps are plastic, then you will require a plastic port to avoid damage to the string. One end of the adapter fits on the plastic tail of the tap and also the other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will need minimizing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the mounting hole in the bath/basin guaranteeing that the washers remain in area between the tap and also the sink. Protect the faucet in position with the manufacturer offered backnut. As soon as the faucet is safely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with typical faucet adapters. The previous type needs to be attached to the tap finishes initially, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Mounting the Bathtub
Utilizing the two wood boards under its feet, place the bathtub in the called for position. The wood boards are valuable in uniformly spreading out the weight of the bath tub over the location of the boards rather than concentrating all the weight onto 4 little factors.
The following goal is to ensure that the bath tub is leveled all round. This can be achieved by checking the spirit level as well as adjusting the feet on the bath tub until the spirit level reviews degree.
To install taps, fit all-time low of the furthest adaptable faucet port to the proper supply pipe by making a compression join; after that do the same for the other faucet.
Activate the water and also examine all joints and brand-new pipework for leakages as well as tighten them if required. Fill up the tub as well as also inspect the overflow outlet and the typical electrical outlet for leakages.
Lastly, fix the bath paneling as described in the supplier's instruction manual. Tiling and also sealing around the bath tub should wait till the bath tub has actually been used at the very least once as this will settle it right into its last position.
Planning for the Setup
Firstly, the supporting structure provided with the bath ought to be fitted (if called for) according to the producer's guidelines. Next off, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is important to see to it that if the tap comes with a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps unit to prevent stress on the tub.
Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet via the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you use every one of the supplied washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bath must now be ready to be fitted in its last placement.
Tiling Around the Tub
In the location where the bath satisfies the tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to split an inflexible seal, creating the water to penetrate the wall surface in between the bath as well as the tiling, bring about issues with dampness and possible leakages to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and can securing voids as much as a size of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with spins of drenched newspaper or soft rope. Remember to always load the tub with water before sealing, to allow for the activity experienced when the tub is in use. The sealant can break fairly early if you do not think about this motion before sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also easily offered on the market. It is suggested to fit the floor tiles utilizing waterproof or waterproof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I discovered that post about How to Install a Bathtub Yourself when looking around the search engines. Are you aware of somebody who is fascinated by the topic? Take a moment to promote it. I value reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Act before it's late!